How do i attach the background on an aquarium

Just had to say I love posts like this. DO NOT attempt to cut the background while it is on the tank.

I used a paper towel and dipped it in oil then wiped that evenly across the background.

How do i attach the background on an aquarium. Below are the steps for the best way to attach an aquarium background. Before you purchase the aquarium background measure your fish tank. You want to know the exact dimensions to ensure that the background will fit.

I dont like to see the back wall when I look at my aquariums so I always attach a background poster to my tanks and this is how I do it. You can create a background for your aquarium in one of two basic ways. You can create the background and attach it to the outside of the tank or you can place the background on the inside.

Whichever way you choose youll need to do some measuring and make sure that over time whatever you use for your background doesnt come undone or otherwise start to. The best way to apply a plastic background such as the Marina styles to the tank is to take a sponge and wet the side of the background you wish to display. Press the background onto the glass and smooth out any possible air bubbles.

You can place some scotch tape on the corners to be sure it will stay in place. Refuse the temptation to just grab the background at the corners and edges with ordinary scotch tape. With this method of mounting air and water flowing down the walls of the aquarium from under the cover can penetrate between the.

You can use a spray bottle and mist the tank with water and the do the same to the background. You dont want it too wet but the moisture makes it easier to smooth out any bubbles. After you apply it to the tank use a credit card.

Cover the tank with a towel so none can get in and just go for it. The bond is strong enough to hold the background on but light enough to easily peel off. And the glue comes up like a thin rubbery coating so its easy to peel off excess.

Just had to say I love posts like this. Some 3D background attach directly to the tank walls with silicon or equivalent we find the Gold label pond and aquarium sealer is perfect for attaching these types of backgrounds and other types that do not float and are thin but allow for water behind them so water capacity is not decreased as much however you run the risk of fish getting behind the background in this. Place the background on a flat surface with the side you want to see in the back of your tank up.

Put a glob of petrol jelly on the middle and smooth it out to a very fine layer all over the front of the background. When its all smeared place it on the back of your tank leaving out all air bubbles. Did you notice that your background is.

About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. If youve ordered a background in 2 sections or more you need to first slide the first section of background with tabs mounted behind and then slide the second section of background and connect both pieces together. You just need to slide the background inside your aquarium.

You can have water in your fish tank and even fish and other decoration. Lay the background picture side up on newspaper. Apply mineral oil to a cotton ball and rub a light layer of mineral oil to the entire surface of the background.

Line the background up with the back of the fish tank so that the top edge fits underneath the aquarium trim piece. Smooth the background on by hand. How to get an Aquarium as your Desktop Background Xp Vista Windows 7 - YouTube.

How to get an Aquarium as your Desktop Background Xp Vista Windows 7 Watch later. Background for aquarium glued as follows. Take the background and attach it with small pieces of scotch.

Then straighten so that there is not a single air bubble. This can be done with a roller you can use other items that have a flat side. Move the background to an appropriate cutting surface such as a craft mat or cutting board and carefully cut the excess material off of the bottom edge using an Exacto knife razor blade or scissors BEFORE APPLYING the background to the tank.

DO NOT attempt to cut the background while it is on the tank. Spritz on some water place the background then start with the squeegee in the middle of the background working from the centre outward to the edges. Make sure you push out every single air bubble which may take some time.

Once you get that done it will last a very long time and should look very clean. Jan 18 2014. I have used cooking oil before in fact almost all of my tanks use this method or just spray paint.

What i do is get to much background put it on the tank and use a razor blade to cut it to the right size then add just a small amount of oil to the tank and then smooth it all over the glass put on the background and take a. I used a paper towel and dipped it in oil then wiped that evenly across the background. I never put any directly on the tank and it worked fine.

Im sure either method will work fine it just seems like the least amount used to get the job done gives the best contact.